Fittings-manufacture,factory,supplier from China

flange connections, which are used for two kinds of pipes, fittings, or devices, are first fixed in a flange flange, and between the two flanges, flange pads are bolted together, which completes the connection. Some pipe fittings and equipment have their own flange, also belong to the flange connection. Flange connection is an important connection mode in pipeline construction. Flange connection is easy to use and can withstand greater pressure. Flange connection is widely used in industrial pipeline. In the home, the pipe diameter is small, and is low pressure, not visible flange connection.

This St andard covers pressure–t emperature  ratings, materials, dimensions, tolerances, marking, testing, and methods of designat ing openings for pipe  flanges and flanged fittings. Included are                                             Production Process:Our group:Jinan Jiang Hua Forging Machinery Co.,Ltd was established in 1995.

1. Each flange or pipe fittings is wiped after ultrasonic cleaning.2. Each flange or pipe fittings is individually packaged with bubble protective film and placed in a wooden box.3. All products are packed in plywood boxes. For larger size flanges, packed in plywood pallets. Or you can customize the packaging by yourself.4. Shipping marks can be made as required5. Product label can be engraved or printed.

Flanged fittings with rating class designation400, 600, 900, and 1500 in sizes NPS 1⁄2 through NPS 24and flanged fittings with rating class designation 2500in sizes 1⁄2 through NPS 12 that are acknowledged inNonmandatory Appendix E in which only U.S.Customary units are provided 1. Standard:DIN2502,DIN2503,DIN2527,DIN2566.DIN2573,DIN2576; DIN2633 ; DIN2632; DIN2631;DIN25662. Type:Plate flange, Threaded, Irrigation,Blind, Lap Joint flange.3. Pressure Class:PN6;PN10; PN16; PN25; PN40; 4. Dimension:DN10-20005.

Blind Flanges. Blind flanges need not be facedin the center if, when this center part is raised, its diameter is at least 25 mm (1 in.) smaller than the inside diameter of fittings of the corresponding pressure class, as given in Tables 9 and 12 (Tables II-9 and II-12) or25 mm (1 in.) smaller than the mating pipe inside diameter.  1. Standard:GOST 12820- 80  GOST 12821- 80 2. Type:Plate flange, Threaded, Irrigation,Blind, Lap Joint flange. Type3. Pressure Class:PN6;PN10; PN16; PN25; PN40; 4. Dimension:DN10-20005.

ASME/ANSI B16.1 - 1998 - Cast Iron Pipe Flanges and Flanged Fittings -Class 125 Flanges - outside and inside diameters, bolt circles, numbers and diameters of bolts  1. Standard:ASME B16.5; ASME B 16.47 Series A(MSS SP-44); ASME B 16.47 Series BAWWA C2072. Type:Plate flange, Slip on ,Threaded, Irrigation,Blind, Lap Joint flange.3. Pressure Class:Class 150; Class 300;Class 400;Class 600;Class 900;Class 1500;Class 25004. Size1/2"-48"5. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6. Raw Material:A105; A105N7.

(1) flanges and flanged fittings made from cast orforged materials (2) blind flanges and certain reducing flanges made from cast, forged, or plate materials1. Standard:DIN2502,DIN2503,DIN2527,DIN2566.DIN2573,DIN2576; DIN2633 ; DIN2632; DIN2631;DIN25662. Type:Plate flange, Threaded, Irrigation,Blind, Lap Joint flange.3. Pressure Class:PN6;PN10; PN16; PN25; PN40; 4. Dimension:DN10-20005. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6. Raw Material:RST 37.2; P245GH ; S235JR7. PackingWooden Case, Pallet.8. Payment:L/C, T/T, Western Union, PayPal9.

PVC pipes,pipe fittings and valves is widely used in water supply,chemical industry,water treatment,enviromental protection,pharmaceutical area etc.It has following advantages:Light weightHigh strengthLow resistanceCorrosion resistanceEasy installationLong service lifeLow costNon-toxic and sanitationProduct Specification: 1. Standard:ASME B16.5; ASME B 16.47 Series A(MSS SP-44); ASME B 16.47 Series BAWWA C2072. Type:Plate flange, Slip on ,Threaded, Irrigation,Blind, Lap Joint flange.3. Pressure Class:Class 150; Class 300;Class 400;Class 600;Class 900;Class 1500;Class 25004.

Flanged fittings with rating class designation 150 and 300 in sizes NPS 1 ⁄2 through NPS 24, with requirements given in both metric and U.S. Customary units with diameter of bolts and flange bolt holes expressed in inch unitsProduct Specification: 1. Standard:ASME B16.5; ASME B 16.47 Series A(MSS SP-44); ASME B 16.47 Series BAWWA C2072. Type:Plate flange, Slip on ,Threaded, Irrigation,Blind, Lap Joint flange.3. Pressure Class:Class 150; Class 300;Class 400;Class 600;Class 900;Class 1500;Class 25004. Size1/2"-48"5.

Used for the connection between the tube end  in chemical, construction, water supply, drainage, oil and gas, light and heavy industrial, refrigeration, sanitation, plumbing, fire protection, electrical, aerospace, shipbuilding and other infrastructure projects

Pressure–temperature ratings are maximum allowable working gage pressures in bar units at the temperatures in degrees Celsius shown in Tables 2-1.1 through  2-3.19 for the applicable material and class designation.  Tables II-2-1.1 through II-2-3.19 of Mandatory  Appendix II list pressure–temperature ratings using psi  units for pressure at the t emperature in degrees  Fahrenheit. For intermediate temperatures, linear interpolation is permitted. Interpolation between class designations is not permitted.  

Our group:Jinan Jiang Hua Forging Machinery Co.,Ltd was established in 1995. The company located in the eastern suburd of Jinan,possesses a favorable position: with Jinan International Airport to its west and Qingdao Port to its east. The company covers 48000 square meters, has 38,000,000,000 RMB investment and possesses 360 staffs and more than 30 technicians.

Production Process:Our group:Jinan Jiang Hua Forging Machinery Co.,Ltd was established in 1995. The company located in the eastern suburd of Jinan,possesses a favorable position: with Jinan International Airport to its west and Qingdao Port to its east. The company covers 48000 square meters, has 38,000,000,000 RMB investment and possesses 360 staffs and more than 30 technicians.

Material:But according to ASTM, JIS, DIN, GB standardASTM: 304, 304 L, 316 L, 316, and 316 Ti, 317, 317 L, 321, 321 H, etcJIS: SUS304, SUS304L, SUS316 SUS316L, SUS316Ti, SUS317L, SUS321, SUS321H, etcDIN: 1.4301, 1.4306, 1.4401, 1.4435, 1.4571, 1.4436, 1.4438, 1.4541, etcGB: 0 Cr18N9, 00 Cr19Ni101. Standard:BS4504 2. Type:Plate flange, Threaded, Irrigation,Blind, Lap Joint flange. Type3. Pressure Class:PN6;PN10; PN16; PN25; PN40; 4. Dimension:DN10-20005. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6.

Any spot facing or back facing shall not reduce the flange thickness to less than the flange thicknessspecified. When spot facing is used, the diameter shall be large enough to accommodate the outside diameter of the equivalent normal series of washers in accordance with EN ISO 887 for the bolt size being fitted. The bearing surfaces for the bolting shall be parallel to the flange face within the limits given in Table 22. When a flange is back faced a minimum fillet radius, R2 (see Figure 17) in accordance with Table 23 shall be maintained.1.

A blind flange is a solid flange as shown below. The purpose of these is to block off a section ofpipe or a nozzle on a vessel that is not used. (A nozzle is typically a pipe coming out of a vessel and is usually flanged so it can be connected to valves or piping). Many times a nozzle will be blanked off with a blind flange for pressure tests in a plant, or simply because the customer does not need all the nozzles that were supplied on the tank.1. Standard:GOST 12820- 80  GOST 12821- 80 2. Type:Plate flange, Threaded, Irrigation,Blind, Lap Joint flange. Type3.

When building a pipeline, the length of the pipes used are not always known. By manufacturing the pipe separate from the flange plate, the welders can cut the pipe to length and weld a flange plate in place to join the pipes at any needed length. The plates can also be welded to the pipe on a slight bias, allowing two pipes to be joined that may not be precisely lined up.1. Standard:ASME B16.5; ASME B 16.47 Series A(MSS SP-44); ASME B 16.47 Series BAWWA C2072. Type:Plate flange, Slip on ,Threaded, Irrigation,Blind, Lap Joint flange.3.

Face finish: The finish on the face of flange is measured as an Arithmetical Average Roughness Height(AARH). The finish is determined by the standard used. For example, ANSI B16.5 specifies face finishes within a range 125AARH-500AARH(3.2Ra to 12.5Ra). Other finishes are available on requst, for example 1.6 Ra max,1.6/3.2 Ra, 3.2/6.3Ra or 6.3/12.5Ra. The range 3.2/6.3Ra is most common.1. Standard:JIS B2220 2. Type:SOP; SOH3. Pressure Class:5k;10k;16k;40k4. Dimension:DN10-20005. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6. Raw Material:SS4007.

In addition to the range of PN 2,5 to PN 40 DIN origin flanges contained in the ISO standard, EN 1092-1 also includes flanges up to PN 400. 1. Standard:BS4504 2. Type:Plate flange, Threaded, Irrigation,Blind, Lap Joint flange. Type3. Pressure Class:PN6;PN10; PN16; PN25; PN40; 4. Dimension:DN10-20005. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6. Raw Material:RST 37.2; P245GH ; S235JR7. PackingWooden Case, Pallet.8. Payment:L/C, T/T, Western Union, PayPal9. Delivery time:30 ~60 days after confirm the order

Flange plate designs are uniform in any given size regardless of materials used to create them. This allows a 6-inch (15 cm) black pipe flange to mate perfectly with a 6-inch stainless steel flange. The flange plates will have a serrated finish on the inside mating surface, which allows the plate to seat into the gasket material. This ensures a perfect seal between two joining pipes.1. Standard:JIS B2220 2. Type:SOP; SOH3. Pressure Class:5k;10k;16k;40k4. Dimension:DN10-20005. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6. Raw Material:SS4007.

In addition to the range of PN 2,5 to PN 40 DIN origin flanges contained in the ISO standard, EN 1092-1 alsoincludes flanges up to PN 400. 1. Standard:BS4504 2. Type:Plate flange, Threaded, Irrigation,Blind, Lap Joint flange. Type3. Pressure Class:PN6;PN10; PN16; PN25; PN40; 4. Dimension:DN10-20005. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6. Raw Material:RST 37.2; P245GH ; S235JR7. PackingWooden Case, Pallet.8. Payment:L/C, T/T, Western Union, PayPal9. Delivery time:30 ~60 days after confirm the order1. Standard:BS4504 2.

Flanges Introduction:A flange is a method of connecting pipes, valves, pumps and other equipment to form a pipework system. It also provides easy access for cleaning, inspection or modification. Flanges are usually welded or crewed into such systems and then joined with bolts.Product Specification:1. Standard:EN1092-1 2. Type:Type 01 ;Type 02; Type 05; Type11; Type12; Type133. Pressure Class:PN6;PN10; PN16; PN25; PN40; 4. Dimension:DN10-20005. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6. Raw Material:RST 37.2; P245GH ; S235JR7.

whereas ISO 7005-1 included in its scope both the original DIN based flanges and also the originalANSI/ASME based flanges, EN 1092-1 contains only the PN based flanges. CEN/TC 74 has produced a separate series of standards, EN 1759-1, EN 1759-3 and EN 1759-4, dealing with the ANSI/ASME based flanges in their original Class designations;1. Standard:BS4504 2. Type:Plate flange, Threaded, Irrigation,Blind, Lap Joint flange. Type3. Pressure Class:PN6;PN10; PN16; PN25; PN40; 4. Dimension:DN10-20005. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6.

A flange is a method of connecting pipes, valves, pumps and other equipment to form a pipework system. It also provides easy access for cleaning, inspection or modification. Flanges are usually welded or crewed into such systems and then joined with bolts.Product Specification:1. Standard:GOST 12820- 80  GOST 12821- 80 2. Type:Plate flange, Threaded, Irrigation,Blind, Lap Joint flange. Type3. Pressure Class:PN6;PN10; PN16; PN25; PN40; 4. Dimension:DN10-20005. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6.