Monel flange-manufacture,factory,supplier from China

Flange types:Weld NeckThis flange is circumferntially welded into the system at its neck which means that the integrity of the butt welded area can be easily examined by radiography. The bores of both pipe and flange match, which reduces turbulence and erosion inside the pipeline. The weld neck is therefore favoured in critical applications.Slip OnThis flange is slipped over the pipe and then fillet welded. Slip-on flanges are easy to use in fabricated applications.BlindThis flange is used to blank off pipelines, valves and pumps, it can also be used as an inspection cover.

A blind flange is a solid flange as shown below. The purpose of these is to block off a section ofpipe or a nozzle on a vessel that is not used. (A nozzle is typically a pipe coming out of a vessel and is usually flanged so it can be connected to valves or piping). Many times a nozzle will be blanked off with a blind flange for pressure tests in a plant, or simply because the customer does not need all the nozzles that were supplied on the tank.1. Standard:GOST 12820- 80  GOST 12821- 80 2. Type:Plate flange, Threaded, Irrigation,Blind, Lap Joint flange. Type3.

Coating: black paint, yellow transparent paint, cold and hot dip galvanizePackage: sea worthy plywooden case, wooden pallet1. Standard:GOST 12820- 80  GOST 12821- 80 2. Type:Plate flange, Threaded, Irrigation,Blind, Lap Joint flange. Type3. Pressure Class:PN6;PN10; PN16; PN25; PN40; 4. Dimension:DN10-20005. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6. Raw Material:RST 37.2; P245GH ; S235JR7. PackingWooden Case, Pallet.8. Payment:L/C, T/T, Western Union, PayPal9. Delivery time:30 ~60 days after confirm the order1.

Any spot facing or back facing shall not reduce the flange thickness to less than the flange thicknessspecified. When spot facing is used, the diameter shall be large enough to accommodate the outside diameter of the equivalent normal series of washers in accordance with EN ISO 887 for the bolt size being fitted. The bearing surfaces for the bolting shall be parallel to the flange face within the limits given in Table 22. When a flange is back faced a minimum fillet radius, R2 (see Figure 17) in accordance with Table 23 shall be maintained.1.

Weld neck flange, slip on flange, blind flange, lap joint flange, loose flange, plate flange , threaded flange, socket weld flange, orifice flange, anchor flange, tubesheet flange,spectacle blind, paddle space, paddle blank, long weld neck flange,  customized1. Standard:JIS B2220 2. Type:SOP; SOH3. Pressure Class:5k;10k;16k;40k4. Dimension:DN10-20005. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6. Raw Material:SS4007. PackingWooden Case, Pallet.8. Payment:L/C, T/T, Western Union, PayPal9. Delivery time:30 ~60 days after confirm the order1.

Q: Can you produce the products according to my own drawings?A: Yes, we can produce the products according to your drawings.we have profession engineers in our factory .1. Standard:ASME B16.5; ASME B 16.47 Series A(MSS SP-44); ASME B 16.47 Series BAWWA C2072. Type:Plate flange, Slip on ,Threaded, Irrigation,Blind, Lap Joint flange.3. Pressure Class:Class 150; Class 300;Class 400;Class 600;Class 900;Class 1500;Class 25004. Size1/2"-48"5. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6. Raw Material:A105; A105N7. PackingWooden Case, Pallet.8.

When building a pipeline, the length of the pipes used are not always known. By manufacturing the pipe separate from the flange plate, the welders can cut the pipe to length and weld a flange plate in place to join the pipes at any needed length. The plates can also be welded to the pipe on a slight bias, allowing two pipes to be joined that may not be precisely lined up.1. Standard:ASME B16.5; ASME B 16.47 Series A(MSS SP-44); ASME B 16.47 Series BAWWA C2072. Type:Plate flange, Slip on ,Threaded, Irrigation,Blind, Lap Joint flange.3.

1. Standard:DIN2502,DIN2503,DIN2527,DIN2566.DIN2573,DIN2576; DIN2633 ; DIN2632; DIN2631;DIN25662. Type:Plate flange, Threaded, Irrigation,Blind, Lap Joint flange.3. Pressure Class:PN6;PN10; PN16; PN25; PN40; 4. Dimension:DN10-20005. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6. Raw Material:RST 37.2; P245GH ; S235JR7. PackingWooden Case, Pallet.8. Payment:L/C, T/T, Western Union, PayPal9. Delivery time:30 ~60 days after confirm the order1. Standard:DIN2502,DIN2503,DIN2527,DIN2566.DIN2573,DIN2576; DIN2633 ; DIN2632; DIN2631;DIN25662.

  The pressure marking specified in this standard is divided into PN marking and Class marking.PN marking has 12 pressure ratingsThey are: PN2.5; PN6; PN10; PN16; PN25; PN40; PN63; PN100; PN160; PN250; PN320; PN4001. Standard:ASME B16.5; ASME B 16.47 Series A(MSS SP-44); ASME B 16.47 Series BAWWA C2072. Type:Plate flange, Slip on ,Threaded, Irrigation,Blind, Lap Joint flange.3. Pressure Class:Class 150; Class 300;Class 400;Class 600;Class 900;Class 1500;Class 25004. Size1/2"-48"5. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6.

Flanges Introduction:A flange is a method of connecting pipes, valves, pumps and other equipment to form a pipework system. It also provides easy access for cleaning, inspection or modification. Flanges are usually welded or crewed into such systems and then joined with bolts.Product Specification:1. Standard:DIN2502,DIN2503,DIN2527,DIN2566.DIN2573,DIN2576; DIN2633 ; DIN2632; DIN2631;DIN25662. Type:Plate flange, Threaded, Irrigation,Blind, Lap Joint flange.3. Pressure Class:PN6;PN10; PN16; PN25; PN40; 4. Dimension:DN10-20005.

Rat ings for welding neck flanges covered by this Standard are based upon their hubs at the welding endhaving thickness at least equal to that calculated for pipe having 276 MPa (40,000 psi) specified minimum yieldstrength.1 In order to ensure adequate flange hub thick ness for flange sizes NPS 2 and larger, the bore of awelding neck flange, dimension B in the various dimen sional t ables, shall not exceed Bmax det ermined asfollows: 1. Standard:DIN2502,DIN2503,DIN2527,DIN2566.DIN2573,DIN2576; DIN2633 ; DIN2632; DIN2631;DIN25662.

Flange:Flange is the parts which connects two pipe endsFlange Application:Flange is widely used in constructions, petroleum, chemical industry, power, ship building, paper making, metallurgy, water supply and sewage work, light and heavy industry, plumbing and electric, etc.Flange Type:Flat Plate Flange, Slip-on Flange, Blind Flange, Weld Neck Flange, Threaded Flange, Socket Weld Flange, etc. Flange Standard:ANSI, AWWA, ASME, DIN, EN, BS, JIS, GOST, SABS, etc.1. Standard:DIN2502,DIN2503,DIN2527,DIN2566.DIN2573,DIN2576; DIN2633 ; DIN2632; DIN2631;DIN25662.

Material:But according to ASTM, JIS, DIN, GB standardASTM: 304, 304 L, 316 L, 316, and 316 Ti, 317, 317 L, 321, 321 H, etcJIS: SUS304, SUS304L, SUS316 SUS316L, SUS316Ti, SUS317L, SUS321, SUS321H, etcDIN: 1.4301, 1.4306, 1.4401, 1.4435, 1.4571, 1.4436, 1.4438, 1.4541, etcGB: 0 Cr18N9, 00 Cr19Ni101. Standard:BS4504 2. Type:Plate flange, Threaded, Irrigation,Blind, Lap Joint flange. Type3. Pressure Class:PN6;PN10; PN16; PN25; PN40; 4. Dimension:DN10-20005. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6.

Flange plate designs are uniform in any given size regardless of materials used to create them. This allows a 6-inch (15 cm) black pipe flange to mate perfectly with a 6-inch stainless steel flange. The flange plates will have a serrated finish on the inside mating surface, which allows the plate to seat into the gasket material. This ensures a perfect seal between two joining pipes.1. Standard:JIS B2220 2. Type:SOP; SOH3. Pressure Class:5k;10k;16k;40k4. Dimension:DN10-20005. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6. Raw Material:SS4007.

1.Reasonable price with excellent quality.2.Abundant stock and prompt delivery.3.Rich supply and export experience, sincere service.4.Reliable forwarder, 2-hour away from port.1. Standard:ASME B16.5; ASME B 16.47 Series A(MSS SP-44); ASME B 16.47 Series BAWWA C2072. Type:Plate flange, Slip on ,Threaded, Irrigation,Blind, Lap Joint flange.3. Pressure Class:Class 150; Class 300;Class 400;Class 600;Class 900;Class 1500;Class 25004. Size1/2"-48"5. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6. Raw Material:A105; A105N7.

1. Each flange or pipe fittings is wiped after ultrasonic cleaning.2. Each flange or pipe fittings is individually packaged with bubble protective film and placed in a wooden box.3. All products are packed in plywood boxes. For larger size flanges, packed in plywood pallets. Or you can customize the packaging by yourself.4. Shipping marks can be made as required5. Product label can be engraved or printed.

A flange is a method of connecting pipes, valves, pumps and other equipment to form a pipework system. It also provides easy access for cleaning, inspection or modification. Flanges are usually welded or crewed into such systems and then joined with bolts.Product Specification:1. Standard:GOST 12820- 80  GOST 12821- 80 2. Type:Plate flange, Threaded, Irrigation,Blind, Lap Joint flange. Type3. Pressure Class:PN6;PN10; PN16; PN25; PN40; 4. Dimension:DN10-20005. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6.

Forged steel Flanges:   1.Flange Types: Slip-On Flange, Welding Neck Flange, Blind Flange, Socket Welding Flange, Threaded Flange, Lap Joint Flange and Plate etc2.Pressure Ratings: 150lbs, 300lbs, 600lbs, 900lbs...3. High quality flanges4. Compective price5. Fast deliveryProduct Specification:1. Standard:BS4504 2. Type:Plate flange, Threaded, Irrigation,Blind, Lap Joint flange. Type3. Pressure Class:PN6;PN10; PN16; PN25; PN40; 4. Dimension:DN10-20005. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6.

whereas ISO 7005-1 included in its scope both the original DIN based flanges and also the originalANSI/ASME based flanges, EN 1092-1 contains only the PN based flanges. CEN/TC 74 has produced a separate series of standards, EN 1759-1, EN 1759-3 and EN 1759-4, dealing with the ANSI/ASME based flanges in their original Class designations;1. Standard:BS4504 2. Type:Plate flange, Threaded, Irrigation,Blind, Lap Joint flange. Type3. Pressure Class:PN6;PN10; PN16; PN25; PN40; 4. Dimension:DN10-20005. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6.

Flanges Introduction:A flange is a method of connecting pipes, valves, pumps and other equipment to form a pipework system. It also provides easy access for cleaning, inspection or modification. Flanges are usually welded or crewed into such systems and then joined with bolts.Product Specification:1. Standard:ASME B16.5; ASME B 16.47 Series A(MSS SP-44); ASME B 16.47 Series BAWWA C2072. Type:Plate flange, Slip on ,Threaded, Irrigation,Blind, Lap Joint flange.3. Pressure Class:Class 150; Class 300;Class 400;Class 600;Class 900;Class 1500;Class 25004. Size1/2"-48"5.

Another layer of carbon steel flange means: according to the size and tolerance range required by the national standard production of flanges, different from the flange pieces not produced according to the standard size is also called two standard flanges (some people call non-standard flanges are incorrect), usually some unscrupulous merchants will reduce the thickness of the flange, the outer diameter of the two dimensions to achieve the purpose of saving materials, and the use of scrap steel or scrap steel1. Standard:EN1092-1 2. Type:Type 01 ;Type 02; Type 05; Type11; Type12; Type133.

In addition to the range of PN 2,5 to PN 40 DIN origin flanges contained in the ISO standard, EN 1092-1 also includes flanges up to PN 400. 1. Standard:BS4504 2. Type:Plate flange, Threaded, Irrigation,Blind, Lap Joint flange. Type3. Pressure Class:PN6;PN10; PN16; PN25; PN40; 4. Dimension:DN10-20005. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6. Raw Material:RST 37.2; P245GH ; S235JR7. PackingWooden Case, Pallet.8. Payment:L/C, T/T, Western Union, PayPal9. Delivery time:30 ~60 days after confirm the order

In addition to the range of PN 2,5 to PN 40 DIN origin flanges contained in the ISO standard, EN 1092-1 alsoincludes flanges up to PN 400. 1. Standard:BS4504 2. Type:Plate flange, Threaded, Irrigation,Blind, Lap Joint flange. Type3. Pressure Class:PN6;PN10; PN16; PN25; PN40; 4. Dimension:DN10-20005. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6. Raw Material:RST 37.2; P245GH ; S235JR7. PackingWooden Case, Pallet.8. Payment:L/C, T/T, Western Union, PayPal9. Delivery time:30 ~60 days after confirm the order1. Standard:BS4504 2.

Flanges Introduction:A flange is a approach of connecting pipes, valves, pumps and other gear to form a pipework system. It additionally provides handy access for cleaning, inspection or modification. Flanges are typically welded or crewed into such systems and then joined with bolts.Product Specification:1. Standard:BS4504 2. Type:Plate flange, Threaded, Irrigation,Blind, Lap Joint flange. Type3. Pressure Class:PN6;PN10; PN16; PN25; PN40; 4. Dimension:DN10-20005.